hex-keyboard or not. small 10x10cm 5x5 keys programmable keyboard
small brother of https://dev.sigpipe.me/DashieElectronics/dashie-keys
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

rules.mk 2.9KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869
  1. # MCU name
  2. #MCU = at90usb1286
  3. MCU = atmega32u4
  4. # Processor frequency.
  5. # This will define a symbol, F_CPU, in all source code files equal to the
  6. # processor frequency in Hz. You can then use this symbol in your source code to
  7. # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  8. # automatically to create a 32-bit value in your source code.
  9. #
  10. # This will be an integer division of F_USB below, as it is sourced by
  11. # F_USB after it has run through any CPU prescalers. Note that this value
  12. # does not *change* the processor frequency - it should merely be updated to
  13. # reflect the processor speed set externally so that the code can use accurate
  14. # software delays.
  15. F_CPU = 16000000
  16. #
  17. # LUFA specific
  18. #
  19. # Target architecture (see library "Board Types" documentation).
  20. ARCH = AVR8
  21. # Input clock frequency.
  22. # This will define a symbol, F_USB, in all source code files equal to the
  23. # input clock frequency (before any prescaling is performed) in Hz. This value may
  24. # differ from F_CPU if prescaling is used on the latter, and is required as the
  25. # raw input clock is fed directly to the PLL sections of the AVR for high speed
  26. # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  27. # at the end, this will be done automatically to create a 32-bit value in your
  28. # source code.
  29. #
  30. # If no clock division is performed on the input clock inside the AVR (via the
  31. # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  32. F_USB = $(F_CPU)
  33. # Interrupt driven control endpoint task(+60)
  34. OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  35. BOOTLOADER = halfkay
  36. # Boot Section Size in *bytes*
  37. # Teensy halfKay 512
  38. # Teensy++ halfKay 1024
  39. # Atmel DFU loader 4096
  40. # LUFA bootloader 4096
  41. # USBaspLoader 2048
  42. OPT_DEFS += -DBOOTLOADER_SIZE=512
  43. # Build Options
  44. # change yes to no to disable
  45. #
  46. BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
  47. MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
  48. EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
  49. CONSOLE_ENABLE = yes # Console for debug(+400)
  50. COMMAND_ENABLE = yes # Commands for debug and configuration
  51. # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  52. SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
  53. # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  54. NKRO_ENABLE = no # USB Nkey Rollover
  55. BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
  56. MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
  57. UNICODE_ENABLE = no # Unicode
  58. BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
  59. AUDIO_ENABLE = no # Audio output on port C6
  60. FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches